:Wanted:
Moderators: BeligerAnt, petec, administrator
- malivoirec
- Posts: 186
- Joined: Fri Mar 09, 2007 9:38 pm
- Location: Tunbridge Wells, Kent
Re: :Wanted:
Hey guys. I'm looking for a member of the forum who has access to a Vacuum former, to make and print me a mould out of Polycarbonate for a project. It's a bit silly as I work for an engineering company and the only tool they (and every manufacturing company in the area I’ve talked to) don't have under the sun is what I'm looking for. I'm happy to pay for materials/labour. PM me if you can help and thanks in advance.
Fortune cookie says: Pain is meerly a feeling;
unless its PERMANANT FOREVER.
Fortune cookie no.2 says: Take heed of
Last cookie
unless its PERMANANT FOREVER.
Fortune cookie no.2 says: Take heed of
Last cookie
Re: :Wanted:
Hey all, I'm looking for some strip board with 1.27mm/0.05" pitch to match that used on the Deltang rx31. My searches thus far have proved fruitless, but I wondered if anyone might have any better ideas where to look?
Thanks in advance.
Thanks in advance.
Scott Fyfe-Jamieson, Captain of Epic Robotics. Champion of AWS38/41/42.
http://www.epicrobotics.co.uk
http://www.epicrobotics.co.uk
Re: :Wanted:
Get some regular strip board and cut the tracks in half? It's what I've always used. I think you can get some on RS, but it's not cheap.
Rory Mangles - Team Nuts
Robots: Nuts 2 and many more...
NanoTwo Motor Controllers: https://nutsandbots.co.uk/product/nanotwodualesc
Robots: Nuts 2 and many more...
NanoTwo Motor Controllers: https://nutsandbots.co.uk/product/nanotwodualesc
- BeligerAnt
- Posts: 1872
- Joined: Wed May 15, 2002 12:00 am
- Location: Brighton
- Contact:
Re: :Wanted:
RS and Farnell sell it, but as Rory says, it's not cheap. If you only have a few 0.050" pitch parts to fit you could look into adapters or just cut some 0.1" pitch board as Rory suggests.
The 0.050" pitch board is often an array of square pads rather than strips so you need to wire between pins somehow.
The 0.050" pitch board is often an array of square pads rather than strips so you need to wire between pins somehow.
Gary, Team BeligerAnt
Re: :Wanted:
Hey people.
Does anyone have any of those 6mm diameter weensy little planetary motors for sale? I would be after 4.
Output speed of 700 + rpm would be handy. Not really fussed about output shaft so long as it has one lol
Cheap and cheerful would be nice
Does anyone have any of those 6mm diameter weensy little planetary motors for sale? I would be after 4.
Output speed of 700 + rpm would be handy. Not really fussed about output shaft so long as it has one lol
Cheap and cheerful would be nice
For my stuff:
http://bodgeitandhope.blogspot.co.uk/
http://bodgeitandhope.blogspot.co.uk/
- joey_picus
- Posts: 1137
- Joined: Tue Jan 13, 2009 1:51 pm
- Location: Lancaster, Lancashire
- Contact:
Re: :Wanted:
This is a bit of a long shot, but does anyone have any of the tiny Parker X-valve (pdf) solenoid valves they wouldn't mind parting with for monetary compensation? (or failing that, a supplier with a low or no minimum order...)
Joey McConnell-Farber - Team Picus Telerobotics - http://picus.org.uk/ - @joey_picus
"These dreams go on when I close my eyes...every second of the night, I live another life"
"These dreams go on when I close my eyes...every second of the night, I live another life"
-
- Posts: 1134
- Joined: Tue Jan 20, 2004 12:00 am
- Location: London
- Contact:
Re: :Wanted:
Sorry Joey my old xvalve is broken. It also has far too little flow for an ant. The rs valve is better.
Does anyone have 1mm grade 5 available I need 3 pieces about 1" by 5" for the aws
Thanks
Does anyone have 1mm grade 5 available I need 3 pieces about 1" by 5" for the aws
Thanks
TEAM GEEK!
-
- Posts: 1134
- Joined: Tue Jan 20, 2004 12:00 am
- Location: London
- Contact: