Search found 153 matches
- Tue Jun 12, 2018 9:42 am
- Forum: Antweights
- Topic: T_Y's Build Log
- Replies: 199
- Views: 317358
Re: T_Y's Build Log
An Arduino controller sounds like an interesting project to do! I'm wondering if it's possible to connect a normal receiver's signal wires to the IO pins on the Arduino instead of using the NRF24LO1, so I can just use the transmitter I've already got instead of custom building one.
- Mon Jun 11, 2018 6:48 pm
- Forum: Antweights
- Topic: T_Y's Build Log
- Replies: 199
- Views: 317358
Re: T_Y's Build Log
Ah okay, that explains the low cost.
- Mon Jun 11, 2018 5:41 pm
- Forum: Antweights
- Topic: T_Y's Build Log
- Replies: 199
- Views: 317358
Re: T_Y's Build Log
I've spent some time trying to slim down Percussive Maintenance to get it into the weight allowance. A tail armour panel was added to keep the wires in and the wiring has been tidied up somewhat so it fits inside the shell completely. It's a very tight fit though. I trimmed down some screws and perf...
- Sat Jun 09, 2018 2:36 pm
- Forum: Antweights
- Topic: T_Y's Build Log
- Replies: 199
- Views: 317358
Re: T_Y's Build Log
@DieGracefullyRobotics
Oh yeah, it didn't occur to me that there would be a weight issue with paint.
@Derek Dudge
War of the axebots!
Oh yeah, it didn't occur to me that there would be a weight issue with paint.
@Derek Dudge
War of the axebots!
- Sat Jun 09, 2018 11:50 am
- Forum: Antweights
- Topic: T_Y's Build Log
- Replies: 199
- Views: 317358
Re: T_Y's Build Log
So for the past few days, every available surface in my room has looked like a robot vomited all over it, while I've been sorting out the wiring. I've cut a larger shell, gaining about 6mm height and 1.5cm in the tail, and I can juuuuuuust about fit everything in, aside from some wires that need sho...
- Thu Jun 07, 2018 7:54 pm
- Forum: Antweights
- Topic: T_Y's Build Log
- Replies: 199
- Views: 317358
Re: T_Y's Build Log
@Paulmchurd
I'm a short cycle away, that would actually be quite handy, thanks. Want to discuss in PM?
I'm a short cycle away, that would actually be quite handy, thanks. Want to discuss in PM?
- Wed Jun 06, 2018 6:30 pm
- Forum: Antweights
- Topic: T_Y's Build Log
- Replies: 199
- Views: 317358
Re: T_Y's Build Log
Quick update, I've been doing some wiring and soldering today. The weapon ESC arrived, so now I have everything except some more motor mounts.
Looks like I was right, the current shell is too small, so it's back to the Sketchup model to get some extra space inside.
Looks like I was right, the current shell is too small, so it's back to the Sketchup model to get some extra space inside.
- Tue Jun 05, 2018 11:11 pm
- Forum: Antweights
- Topic: T_Y's Build Log
- Replies: 199
- Views: 317358
Re: T_Y's Build Log
Thanks everyone! As I said earlier, I do want to re-cut the panels at some point, but for now the shell will suffice. @paulmchurd I picked up a Monoprice Maker Select Plus on Amazon for £290, it's amazing so far. I think it's just a rebrand of the Wanhao that you've got? I have not had the chance to...
- Tue Jun 05, 2018 4:05 pm
- Forum: Antweights
- Topic: T_Y's Build Log
- Replies: 199
- Views: 317358
Re: T_Y's Build Log
It's been a while since the last update! My exams are over now, so I can dedicate a lot more time to getting the bots up and running for the end of the month. So I maaaayyyyy have treated myself and picked up a 3D printer... I've spent a fair amount of time printing off random bits and bobs. I'm dis...
- Tue Jun 05, 2018 12:38 am
- Forum: Antweights
- Topic: My 1st Build & More questions than answers.
- Replies: 7
- Views: 6146
Re: My 1st Build & More questions than answers.
Hi there! I'm running the same setup in one of my bots. If it helps, here is an adapted wiring diagram for just the drive element (Brown is signal, Red is power, Black is ground), assuming you are mixing the elevator and aileron channels on the transmitter (I'm using a Devo 7e for this): https://i.i...