NanoTwo Kits

Rapidrory · Post by **Rapidrory** » Thu Mar 08, 2018 9:18 pm

Yeah MG90s aren't keen on 7.2v. The V3 was aimed at the high voltage servos which are now becoming common in the sport. You'll either have to get a servo that can handle the voltage, or get a 5v BEC to run the servo.

sgtbeardy · Post by **sgtbeardy** » Thu Mar 08, 2018 11:27 pm

I guess I'm ordering a 306G-HV then.

Rogg · Post by **Rogg** » Mon Mar 12, 2018 7:57 pm

I have an older NanoTwo and it's great, however I much prefer tank style steering. Is there any plans to make these available without mixing?

Rapidrory · Post by **Rapidrory** » Wed Mar 14, 2018 10:02 am

No, however it can be achieved fairly easily using the mixing on the TX to negate the built in mixing.

Zanbots · Post by **Zanbots** » Wed Mar 28, 2018 8:42 pm

What's the best way to get hold of Alex or Rory regarding repairs? My friend has sorted out his brand new V3 when checking it over.

GeorgeR · Post by **GeorgeR** » Thu Mar 29, 2018 7:54 pm

Shakey's the contact for all nanotwo tech enquiries now, probably the best bet is to email him, the address is on the Nuts and bots site.

Shakey · Post by **Shakey** » Thu Mar 29, 2018 10:29 pm

GeorgeR wrote: ↑
Thu Mar 29, 2018 7:54 pm
Shakey's the contact for all nanotwo tech enquiries now, probably the best bet is to email him.

Hi,
The contact information can be found in the information of the site.
https://nutsandbots.co.uk/information/

George please could I ask you to remove the email address from your post? Bots crawl this pretty often and it just ends up getting spammed drowning out people I need to talk to.

GeorgeR · Post by **GeorgeR** » Fri Mar 30, 2018 6:35 am

Done, you'll need to edit your post too, it's in the quote.
Hope I haven't caused you too much spam.

Smillard · Post by **Smillard** » Mon Apr 02, 2018 10:41 am

Hi Alex and Rory,

Do you think the next batch will be ready before the next event? Im builing a second and need to work out my shopping list!

If they will come available again, it one less thing for me to worry about!

Rapidrory · Post by **Rapidrory** » Tue Apr 03, 2018 7:14 am

Next batch may not be for a while; I'm out of the country for a few weeks.. hopefully I can get at least another batch done before next event though.

Smillard · Post by **Smillard** » Tue Apr 03, 2018 8:21 am

Thanks Rory,

Ill hold out as long as i can as they would be my preferance but will bear in mind i need a back up option!

James Bennett · Post by **James Bennett** » Sun Apr 22, 2018 10:02 pm

I am thinking about running a NanoTwo V3 on 3 or 4S, for purely innocent, non doom spinner related reasons, honest...

Can I just pass 5V into the servo connector from the weapon ESC?

Rapidrory · Post by **Rapidrory** » Sun Apr 22, 2018 10:05 pm

Should work... though you'll need a decent BEC to power it.

James Bennett · Post by **James Bennett** » Mon Apr 23, 2018 8:56 pm

Thanks Rory.

Yeah, I already managed to buy some ESCs with only 0.5A BECs

.

Rapidrory · Post by **Rapidrory** » Sat Dec 08, 2018 12:24 pm

Latest batch is up! https://nutsandbots.co.uk/product/nanotwov3dualesc/

Robotwars101.org

NanoTwo Kits

Re: NanoTwo Kits

Re: NanoTwo Kits

Re: NanoTwo Kits

Re: NanoTwo Kits

Re: NanoTwo Kits

Re: NanoTwo Kits

Re: NanoTwo Kits

Re: NanoTwo Kits

Re: NanoTwo Kits

Re: NanoTwo Kits

Re: NanoTwo Kits

Re: NanoTwo Kits

Re: NanoTwo Kits

Re: NanoTwo Kits

Re: NanoTwo Kits