Using multiple small LiPos

Please post all questions and answers in here. This way people can easily see if someone else has the same problem.

Moderators: BeligerAnt, petec, administrator

Post Reply
dcr raptor
Posts: 50
Joined: Fri Jan 04, 2013 3:21 am
Location: Capel le Ferne

Using multiple small LiPos

Post by dcr raptor »

Hello,

Since the design of one of my robots is too small for the batteries I currently use, I've needed to look for smaller alternatives.

I've managed to find some 3.7V 100mAh LiPos that should work, however to get the power I need, I will need to use at least 2 LiPos.

I've come up with the following solutions:
2 in series - 7.4V 100mAh
2 in parallel - 3.7V 200mAh
4 LiPos with 2 series of 2 batteries wired in Parallel - 7.4V 200mAh
Circuit 1.png
Circuit 1.png (3.41 KiB) Viewed 8014 times
Please can you give me some guidance as to what would be safe and suitable for a typical 4 wheel push-bot or a 2 wheeled non-spinner?
User avatar
BeligerAnt
Posts: 1872
Joined: Wed May 15, 2002 12:00 am
Location: Brighton
Contact:

Re: Using multiple small LiPos

Post by BeligerAnt »

Generally best not to connect cells in parallel. They will have (slightly) different voltages and the one at the higher voltage will discharge into the one at the lower voltage - with nothing to limit the current!
No problem with connecting cells in series - that's what all battery packs do.
7.2V @ 100mAh is enough for a 2WD robot, although you may have to replace/recharge batteries between fights.
I've never built a 4WD robot so can't comment on needed capacity. I'm sure someone else will chime in...

One thing to look for is the discharge rate of the cells. This is specified in "C" and is a multiplier of the capacity expressed as current. So, for example, a 100mAh battery with a 10C discharge rate can operate at 100 x 10 = 1000mA (peak) although you won't get that much current for very long! For modern cells with discharge rates of 25-30C this is less of a problem, but it's something to be aware of.
Gary, Team BeligerAnt
dcr raptor
Posts: 50
Joined: Fri Jan 04, 2013 3:21 am
Location: Capel le Ferne

Re: Using multiple small LiPos

Post by dcr raptor »

Discharge rate appears to be 2C, so it will peak at 200mA.

I'm planning to use Pololu HP motors.
Motor stats are as follows:

Free-run speed @ 6V:
1000 rpm

Free-run current @ 6V:
120 mA

Stall current @ 6V:
1600 mA

Stall torque @ 6V:
9 oz·in

Motor type:
1.6A stall @ 6V (HP 6V)

Would a battery of 7.4V, 100mAh, 2C be able to run these for the duration of a fight?
User avatar
BeligerAnt
Posts: 1872
Joined: Wed May 15, 2002 12:00 am
Location: Brighton
Contact:

Re: Using multiple small LiPos

Post by BeligerAnt »

Two motors at 120mA each (free-running, so about the lowest current you are likely to see) is more than 200mA. Are you sure about the 2C rating, as it's very low. Can you post a link to the battery specs?
If the discharge rate (different to the charge rate) really is only 2C then the batteries will not be suitable for any competitive antweight robot.
Gary, Team BeligerAnt
dcr raptor
Posts: 50
Joined: Fri Jan 04, 2013 3:21 am
Location: Capel le Ferne

Re: Using multiple small LiPos

Post by dcr raptor »

The batteries I'm looking at are found here:
https://www.powerstream.com/thin-lithium-ion.htm

I'm looking at the 100mAh batteries, though since it doesn't look like these will be decent alternative for an ant, I'll probably need to redesign the body.
User avatar
BeligerAnt
Posts: 1872
Joined: Wed May 15, 2002 12:00 am
Location: Brighton
Contact:

Re: Using multiple small LiPos

Post by BeligerAnt »

It is the very thin size of those batteries that limits the discharge rate. They will (just) cope with 10C discharge so they might just work in an antweight as long as you change them between every fight.
Gary, Team BeligerAnt
Post Reply