TinyTwo Speed Controllers

All things antweight

Moderators: BeligerAnt, petec, administrator

Post Reply
Rapidrory
Posts: 1160
Joined: Sun Nov 24, 2013 9:54 pm

Re: TinyTwo Speed Controllers

Post by Rapidrory »

I've run 10 of those motors off a single N2LV, and also use an N2LV in my 4wd pusher with those motors.. You'll be fine with an LV :P

EDIT: Well, Will has shown that the N2LVHP works 'fine' on 3 cell in Inertia. Very not recommended though! :L
Rory Mangles - Team Nuts

Robots: Nuts 2 and many more...

NanoTwo Motor Controllers: https://nutsandbots.co.uk/product/nanotwodualesc
haz
Posts: 1855
Joined: Thu Apr 15, 2010 11:20 am
Location: Underwater Lair
Contact:

Re: TinyTwo Speed Controllers

Post by haz »

Good stuff, cheers guys!

Boring old 2s for me because height/weight.
danjr1
Posts: 26
Joined: Fri Sep 03, 2010 11:54 am

Re: TinyTwo Speed Controllers

Post by danjr1 »

Do you have any plans for a beetleweight version?
dcr raptor
Posts: 50
Joined: Fri Jan 04, 2013 3:21 am
Location: Capel le Ferne

Re: TinyTwo Speed Controllers

Post by dcr raptor »

Rapidrory wrote:Considering selling these as starter kits:

Image

It's a LemonRX connected and heat shrunk to an N2LV in a really convenient little package; only has 3 sets of wires to worry about and is really small.
Nearly all my robots are based of these; It's just really easy as I can make a bunch of these then throw them in pretty much anything to make an antweight (Mr Burns for example)
Depending on how far I'd take it, the servo could be an optional extra, as would a battery (non lipo)... not sure I'd stretch as far as a transmitter though..

Either that or I don't worry about the motors, wheels etc. and just sell the controller unit..
It all comes down to what there is a market for, and how much time and effort it takes to make and source parts...
The control unit without motors, wheels etc would probably be ~£30... haven't worked out a cost for the full setup yet if I do it.
Would it be possible to buy one of these starter kits at the next AWS?
Rapidrory
Posts: 1160
Joined: Sun Nov 24, 2013 9:54 pm

Re: TinyTwo Speed Controllers

Post by Rapidrory »

Yeah, I hope to have a few to sell at the AWS (if i get any time to put some together before then :roll:). If not, you can pay and leave details, and I'll post one on afterwards.
For more information on them, see: http://robotwars101.org/forum/viewtopic.php?f=1&t=2187
Rory Mangles - Team Nuts

Robots: Nuts 2 and many more...

NanoTwo Motor Controllers: https://nutsandbots.co.uk/product/nanotwodualesc
dcr raptor
Posts: 50
Joined: Fri Jan 04, 2013 3:21 am
Location: Capel le Ferne

Re: TinyTwo Speed Controllers

Post by dcr raptor »

Ok, thanks.
How much are you charging for them?
Rapidrory
Posts: 1160
Joined: Sun Nov 24, 2013 9:54 pm

Re: TinyTwo Speed Controllers

Post by Rapidrory »

It says in the link I just posted; £40
Rory Mangles - Team Nuts

Robots: Nuts 2 and many more...

NanoTwo Motor Controllers: https://nutsandbots.co.uk/product/nanotwodualesc
alasdair
Posts: 563
Joined: Sat Jan 03, 2009 3:52 pm
Location: Marlow, Bucks

Re: TinyTwo Speed Controllers

Post by alasdair »

Pm sent regarding these!
dcr raptor
Posts: 50
Joined: Fri Jan 04, 2013 3:21 am
Location: Capel le Ferne

Re: TinyTwo Speed Controllers

Post by dcr raptor »

Ok, thanks again.
Rapidrory
Posts: 1160
Joined: Sun Nov 24, 2013 9:54 pm

Re: TinyTwo Speed Controllers

Post by Rapidrory »

Just shipped my 100th NanoTwo ESC... It's been a busy 10 months!
Rory Mangles - Team Nuts

Robots: Nuts 2 and many more...

NanoTwo Motor Controllers: https://nutsandbots.co.uk/product/nanotwodualesc
Post Reply