Search found 1002 matches
- Mon Jun 03, 2019 4:42 am
- Forum: Antweights
- Topic: Pneumatic antweight.
- Replies: 13
- Views: 34985
Re: Pneumatic antweight.
Cheers guys. I'll be building this robot after the upcoming AWS now I think and probably debuting it at my event in October. It'll deffinately be an interesting project.
- Sun Jun 02, 2019 7:33 am
- Forum: Antweights
- Topic: Pneumatic antweight.
- Replies: 13
- Views: 34985
Re: Pneumatic antweight.
I have some spare gas bottles from my bb gun so i'll probably use one of them. The aim of this project is to make a crusher that can actually crush things rather than just holding them.
- Sat Jun 01, 2019 8:15 pm
- Forum: Antweights
- Topic: Pneumatic antweight.
- Replies: 13
- Views: 34985
Re: Pneumatic antweight.
Thanks Peter. I think the lego ones are mechanical so I was just going to use an Mg 90 servo to operate the switch. I think I also need some way of pumping it up. For that I was going to use a check valve. I have a couple of those lying around as well as a few T connectors. What are people using for...
- Sat Jun 01, 2019 2:53 pm
- Forum: Antweights
- Topic: Pneumatic antweight.
- Replies: 13
- Views: 34985
Pneumatic antweight.
Hi guys. Could someone please let me know what parts I need to get a basic pneumatic system running? As far as I know I need a gas tank of some sort, a switch, some tubing and a ram. I could be missing a few things but please let me know. I was planning on using mostly lego components, are these gen...
- Fri May 03, 2019 9:52 am
- Forum: Questions (and answers)
- Topic: 5V bec?
- Replies: 6
- Views: 19762
Re: 5V bec?
https://www.unmannedtechshop.co.uk/prod ... xsQAvD_BwE
This is the one I was using when I was using modded servo boards as escs. I doubt you'd need to regulate 2S for a lemon rx though. I hope this helps. ☺
This is the one I was using when I was using modded servo boards as escs. I doubt you'd need to regulate 2S for a lemon rx though. I hope this helps. ☺
- Sun Apr 28, 2019 9:39 am
- Forum: Antweights
- Topic: Esc and Receiver
- Replies: 13
- Views: 31425
Re: Esc and Receiver
I've got a working drive setup going that runs the unbranded chinese ESC. It's a bit on the large side but so long as you shorten the wires and cut off the massive copacitor they aren't too heavy. I use orange rx but that's just me.
- Wed Apr 10, 2019 10:37 am
- Forum: Antweights
- Topic: Pre modded servo boards for escs?
- Replies: 39
- Views: 69885
Re: Pre modded servo boards for escs?
Cheers man. The rx did eventually decide to play ball but its been flashing the red light of doom so I think i'm best of getting a bec for it.
- Wed Apr 10, 2019 9:03 am
- Forum: Antweights
- Topic: Pre modded servo boards for escs?
- Replies: 39
- Views: 69885
Re: Pre modded servo boards for escs?
My Rx doesn't seem to like being run directly on 2 cells. What regulator could I use please?
- Tue Apr 09, 2019 3:49 pm
- Forum: Antweights
- Topic: Axe esc?
- Replies: 3
- Views: 12452
Re: Axe esc?
I will probably have to get a vex 29 for my axe. I think i'd rather not rely on a servo board.
- Sat Apr 06, 2019 8:29 am
- Forum: Antweights
- Topic: Linear actuators
- Replies: 2
- Views: 11244
Re: Linear actuators
Thanks.