Search found 11 matches

by tomboys
Tue Jan 01, 2019 11:44 am
Forum: Questions (and answers)
Topic: Armour /chassis material
Replies: 3
Views: 439

Armour /chassis material

Hello, I have a few questions about making the main body of my robot now I've done the electronics: I've heard about some of the strengths and weaknesses of using hdpe and polycarbonate, but if you were making the chassis/Armour combined out of them, what are the best ways to connect them? I've hear...
by tomboys
Wed Dec 05, 2018 11:49 am
Forum: Questions (and answers)
Topic: Is this right?
Replies: 3
Views: 512

Re: Is this right?

OK, that's alright then (it's not my wiring). I fried it with the soldering iron accidentally, so I need a new board either way. I knew one motor wouldn't work, I just wasn't sure if the fact neither motor worked was due to me not wiring it right!
by tomboys
Wed Dec 05, 2018 10:17 am
Forum: Questions (and answers)
Topic: Is this right?
Replies: 3
Views: 512

Is this right?

I connected up my DasMikro ESC last night and although the receiver lights up and the servo responds to the transmitter, neither motor moves. Although I have only connected one signal wire (I fried one connection and probably need a new ESC), am I right in that at least one motor should still be mov...
by tomboys
Sat Aug 25, 2018 4:07 pm
Forum: Questions (and answers)
Topic: Servo straight to battery
Replies: 1
Views: 348

Servo straight to battery

Just wanted to check that I'm right in assuming that if I'm going to wire the Servo straight to the battery, I just have to cut the positive and negative wires that would normally go to the receiver and connect them straight to the battery.
by tomboys
Thu Aug 02, 2018 8:31 am
Forum: Questions (and answers)
Topic: Increasing numbers
Replies: 18
Views: 1583

Re: Increasing numbers

How about you can enter 4 robots:
1 - roller
2 - roller
3 - walker/cluster
4 - roller (reserve)
by tomboys
Sun Jun 17, 2018 5:32 pm
Forum: Questions (and answers)
Topic: No control
Replies: 9
Views: 560

Re: No control

Hey I recorded a video of my attempts to bind. Before I turned on with the sticks in the correct position (left stick down) The bind plug is in the plug marked batt/bind https://youtu.be/MViQ45Z0PTo Afterwards I turned both off, removed the bind plug, turned back on with the sticks in the same posit...
by tomboys
Fri Jun 15, 2018 1:20 pm
Forum: Questions (and answers)
Topic: No control
Replies: 9
Views: 560

Re: No control

I'll try to take some photos/videos over the weekend. I won't be in the same house as it until Sunday now anyway.
Hopefully the answer will be that despite all my research on how to do everything, I've just done something (small and easy to fix) wrong while binding it. :oops:
by tomboys
Thu Jun 14, 2018 9:21 pm
Forum: Questions (and answers)
Topic: No control
Replies: 9
Views: 560

Re: No control

I haven't got any spares at the moment to be honest, but I have 2 separate speed controllers, and neither motor turns, even if I attach them separately, so I'm starting to think either the transmitter or receiver doesn't work
by tomboys
Thu Jun 14, 2018 9:08 pm
Forum: Questions (and answers)
Topic: No control
Replies: 9
Views: 560

Re: No control

I did leave it until the light came back on :(
by tomboys
Thu Jun 14, 2018 8:46 pm
Forum: Questions (and answers)
Topic: No control
Replies: 9
Views: 560

No control

I just bound my devo 7e (deviation) to an orange rx r410x (dsmx, the light stopped flashing, so I know that it bound) but when I connect the robot to a battery the lights come on, but the transmitter doesn't control anything and nothing spins. I have the signal wire at the top of the receiver, I tur...
by tomboys
Mon Jun 11, 2018 11:22 am
Forum: Antweights
Topic: Robot Name Clearing House
Replies: 12
Views: 939

Re: Robot Name Clearing House

Has anyone used Up the Antie before?